High flow rates are achieved due to the optimized pleat pack density and the superior design construction of TETPOR LIQUID filters. Features and Benefits • Superior chemical resistance of PTFE membrane combined with polypropylene hardware • Integrity tested prior to despatch • Validated to ASTM F838-05 methodology • Comprehensive range
biological fluids and gases is usually done with 0.2 or 0.22 µm pore filter membranes. Clarification and prefiltration of solutions and solvents is best accomplished with 0.45 µm or larger filter membranes. Prefiltration to improve filter performance can also be accomplished by the use of glass fiber prefilters that can be purchased separately.
PTFE Unlaminated Membrane Filters. Our unsupported, hydrophobic, PTFE membrane filters are ideal for sterilization and venting applications involving air, gasses, and solvents/acids incompatible with most other filters. These PTFE filters are chemically and biologically inert, stable up to 260°C, and will withstand the majority of concentrated
EZFlow 25mm, 47mm, and 90mm membrane disc filters are used to retain particles or microorganisms by surface capture. The membrane disc filters are available in 0.22µm or 0.45µm pore sizes. The Hydrophobic PTFE membrane is bonded to a polypropylene support and due to its extreme chemical.
The filter cartridge uses the latest generation of high permeability proprietary PTFE membranes. The filter media encapsulation design was developed using Pall’s unique computer aided design modeling system. This advanced fluid dynamics design provides enhanced lateral flow across, through and out of the membrane. The unrestricted fluid
PTFE membrane filter has excellent chemical stability, resistance to organic solvents and strong acids, corrosion resistance; high-temperature resistance, and low protein binding ability. Smooth surface, high filtration efficiency, and wide application range. See full list on hawachmembrane.com
PTFE membrane filters have an excellent chemical compatibility (pH 1 to 14), so that they are also used for the filtration of solvents and acids, to which other filter types are not resistant. Moreover, they can be used to filter aqueous solutions as well, but, because of their hydrophobic characteristics, they must be pre-wetted with ethanol
Product Support. Whatman PTFE membranes from Cytiva are strong hydrophobic membrane filters resistant to the corrosive solvents and aggressive media used in gas sterilization* and liquid clarification. Polypropylene grid support material for increased strength. Temperature resistant up to 120°C. Resistant to most aggressive acids, alkalis, and
PTFE Membranes CF/2.1/041 Gas and Liquid Flow rates in litres/hr at 0.1 Bar pressure drop Flow rates will depend on which membrane grade is installed in the membrane housing. First check the size of the filter element using the housing data sheets and then refer to the charts below to read the flow rate against the membrane grade.
Aervent-50 0.2 µm hydrophobic filters contain a 50 mm Aervent PTFE membrane in a bi-directionally supported polypropylene casing. This sterilizing-grade filter is designed for critical small scale gas line and air venting applications. The hydrophobic Aervent PTFE membrane provides high
Description. Emflon PFRW cartridges are sterilizing grade hydrophobic membrane filters designed for reliable retention of bacteria and high levels of phages in compressed gas and vent applications. The filter element features Pall's advanced 0.2 micron rated polytetrafluoroethylene (PTFE) double-layer membranes, pleated with very high area into
Ultradyne ® absolute-rated polytetrafluoroethylene (PTFE) membrane filters offer the highest level of assurance of chemical compatibility and filtration performance in aggressive chemicals, prolonged hot air service and other severe process conditions. Ultradyne ® filters’ PTFE membrane delivers superior flow rates and long service life.
0.2 µm Filter Diameter ⌀ 25 mm $329.00 Hydrophobic PTFE Membrane Filters / Type 11807 100 Item no. 11807--13------N Pore Size 0.2 µm Filter Diameter ⌀ 13 mm $276.00 Hydrophobic PTFE Membrane Filters / Type 11807 25 Item no. 11807--90------G Pore Size 0.2 µm Filter Diameter ⌀ 90 mm $493.00 Hydrophobic PTFE Membrane Filters / Type 11842 100 Item no.
Durable, efficient, and broadly compatible, these pure, hydrophilic PTFE membranes are ideal for use with HPLC seperations, aqueous/organic solvents, and many of your other filtration needs. Pack of 100. Pore size: 0.20 microns. Diameter: 13 mm. Advantec P/N: H020A013A.
0.2 um pore size, Hydrophilic PTFE membrane, 47 mm diameter Omnipore Membrane Filter MSDS (material safety data sheet) or SDS, CoA and CoQ, dossiers, brochures and other available documents. Technical Information Data Sheet JGWP04700 100 pack, 0.2 µm, 47 mm, white, plain Price could not be retrieved Recommended Products Overview
