15/9/2020 · PTFE membranes. This new generation of filter sets the standard with an unrivalled combination of efficiency, flow rate and strength. The HIGH FLOW TETPOR II is validated as a 0.2 micron sterilizing grade filter in liquids through ASTM F838-05 in gas through full
HIGH FLOW TETPOR II gas sterilization filters have been developed to benefit from technological advances within the manufacture of PTFE membranes. This new generation of filter sets the standard with an unrivalled combination of efficiency, flow rate and strength.
Millex-FG, 0.20 µm, hydrophobic PTFE, 25 mm A 25 mm diameter sterile syringe filter with a 0.2 µm pore size hydrophobic PTFE membrane, ethylene oxide sterilized.; find Millipore-SLFG025LS MSDS, related peer-reviewed papers, technical documents, similar
The filter element features Pall's advanced 0.2 micron rated polytetrafluoroethylene (PTFE) double-layer membranes, pleated with very high area into single open-end cartridges. They are built to withstand demanding in situ steaming conditions in either the forward or reverse direction.
PTFE Filter Cartridges. Rs 900/ Piece. Pleated Filter Cartridge. Rs 1,150/ Piece. High Efficiency 20" PP Pleated 0.45 Micron Filter Cartridge. Rs 1,150/ Piece. PTFE Pleated Cartridge. Rs 1,150/ Piece. Pleated Filters.
PTFE Filter Cartridge - 0.2 micron. ₹ 3,500/ Piece Get Latest Price. Length. 10 inch,also available in 5 inch,20 inch,30 inch,40 inch. Operating Conditions. 4.2 bar at 23 deg C And 1.5 bar at 80 deg C. Filtration Area. 5.8ft2 per 10 inch. Autoclaving.
25/2/2021 · GasPro ™ TEM-2260 series filters are specifically designed for the filtration of semiconductor gases when ultra-high flow rates are required. This all-welded assembly will deliver 0.003 micron particle retention where a high flow rate is required and space is limited. A PTFE membrane and polypropylene supported cartridge is enclosed in a 316L
• High efficiency contaminant removal at 0.04 μm, 0.1 µm or 0.2 μm micron ratings. • Filtration area from 0.16 m² to 1.04 m². • Available as 50 mm capsules, capsules or cartridges. • Assymetric polyethersulfone membrane with Advanced Pleat Technology • 100%
HIGH FLOW TETPOR II is validated as a 0.2 micron sterilizing grade filter in liquids through ASTM F838-05 and in gas through full retention to an aerosol challenge of MS2 phage. This ensures the filter will guarantee the sterility of your process in the worst-case scenario where the filter may be subjected to bulk liquid due to a process problem.
Minisart® Syringe Filter, Polytetrafluorethylene (PTFE), Pore Size 0.2 µm, Non-Sterile, Female Luer Lock, Male Luer Slip, Pack Size 500 Minisart ® Air with chemically inert hydrophobic PTFE is suitable for venting as well as filtration of gases and oils with a pH of 3 - 12.
IFP PTFE-E Pleated Filter Cartridges use super-hydrophobic, and high flux PTFE membranes have an excellent flow rate and long service life. The filter cartridges are electronic grade and high-purity filters, while flushed with 18.2MΩ.cm ultrapure water and can be
High quality 0.2 Micron Air Filter Hydrophobic PTFE Pleated Sediment Filter from China, China's leading PTFE pleated sediment filter product, with strict quality control hydrophobic pleated sediment filter factories, producing high quality hydrophobic Pleated Filter
• Absolute ratings of 0.05, 0.1, 0.2, 0.4, 1.0 and 5.0 micron deliver precise particle retention at rated level • Highly porous PTFE membrane assures high flow rates, long service life and
Devices feature the fastest flow rate and lowest clogging of comparable alternatives. 0.1um PES available for mycoplasma protection. 0.2um PES devices are stem cell and mouse embryonic assay (MEA) tested. Non-pyrogenic and endotoxin free - Rapid-Flow filter units meet the most rigorous testing standards for any vacuum filtration unit.
