6 Large Flow Cartridges Filter Selection and Sizing Guide Pall large flow cartridges are designed to be very cost effective for flow rates greater than 90 L/min. The recommended flow rate indicated below is provided as a guideline to optimize filter life. Large Flow Cartridge
0 8 7 6 5 4 3 2 1 Vent mode 1 barg inlet 2 barg inlet 3 barg inlet Air Flow Rate (Nm3/h) Please contact Pall for specific application sizing * Pall AGT11 series housing at 20 C (68 F) O-ring Filter Size Module Type Material 05 127 mm (5 in.) 24 1 254
2 Ultrahigh-Purity Gas Filters SCF Series UHP Filters The Swagelok SCF series UHP gas filter is designed to meet the stringent requirements of SEMI E49.8-96. With the proprietary Membralox ceramic element and 316L VAR stainless steel housing, the SCF
A porous form of PTFE (polytetrafluoroethylene), Zitex G exhibits the same chemical inertness, thermal stability and non-wetting characteristics of this outstanding fluoropolymer. Zitex G structures are able to handle virtually any corrosive fluid at temperatures as high as 500 o F (260 o C) and as low as the cryogenic range of -450 o F (-268 o C).
3.1 1.0 1.8 0.8 Number of filters for a 110 gpm flow rate 12 / 30" cartridges 37 / 30" cartridges 21 / 30" cartridges 43 / 30" cartridges * Based on the manufacturers published rating. Table 2: 3M Betapure NT-T Series Filter Ratings Grade Designation T005 1
HYDROPHILIC PTFE FEATURES: Hydrophilic PTFE membrane has good mechanical strength, tear resistance, the contact angle of less than 20 , good bubble point , high porosity, high flow rate. HYDROPHILIC PTFE USED: Hydrophilic PTFE Syringe Filter widely used in sample pre-filtration, clarification, removal of particles, and liquids.
Standard nominal flow rate qnN1) [l/min] Size Micro Pneumatic connection 1, 2 M5 M7 Gx QS-4 QS-6 Pressure regulation range 0.5 7 bar 110 280 410 150 410 1) Measured at p1 = 10 bar, p2 = 6 bar and Δp = 1 bar.-H- 125 l/min must be available for the semi
The Fairchild Model 4100A high precision pressure regulator will handle a 150 psi, 10 BAR maximum supply pressure and offers four (4) output pressure ranges from 0-0.7 psi, 0-0.048 BAR, 0-4.8 kPa up to 0-5 psi, 0-0.35 BAR, 0-35 kPa. The Model 4100A has a flow
Filter Paper Grade 2. Circles: 42.5 mm to 500 mm (available prepleated) Sheets: 460 x 570 mm to 580 x 680 mm. Particle retention 1: 8µm. Nominal thickness: 190 µm. Nominal basis weight: 97 g/m 2. Nominal ash content 2: 0.06%. Grade 2 is slightly more retentive than Grade 1, with an equivalent increase in filtration time.
An ULPA filter is thus defined as a filter having efficiency greater than 99.999% for particles in, typically, the 0.1–0.2 μm size range. HEPA and ULPA filters usually consist of panel frames (as in Figure 3.4 ) containing a mass of deep-pleated filter medium, so as to offer a maximized area of filter medium to the airstream flowing through the filter.
Sterilizing vent filters on autoclaves and Iyophylizers (freeze dryer) Sterile vent filters on product tanks. Sterile air supply for service gases, such as filling lines in blow-fill-seal machines. Sartofluor® cartridges are available in the optimum range of pore sizes – 0.45 µm, 0.2 µm and 0.1 µm.
70mm Disc Test Filter Bench Top Filters Flow Restrictors Industrial Flow Restrictors High Purity Flow Restrictors Flow Restrictors for Healthcare and Lifesciences Drug Delivery Flow Elements Spargers In-Tank Spargers In-Line Spargers Micro Spargers for
8. Filter an aliquot into a 2-mL autosampler vial through a 4-mm, 0.45-µm PTFE filter. CALIBRATION AND QUALITY CONTROL: 9. Determine retention times for thiophanate-methyl using the column and chromatographic conditions as shown on page 5606-1. The
Fluorofil Plus High Flow Sterile Gas Filter with ePTFE Membrane Fluorofil F100 PTFE Membrane Cartridge Filters Hydrofil Nylon 6.6 Membrane Filter Hydrofil Plus Dual Nylon 6.6 Layer Membrane Cartridge Filters Vinofil Double Layer Membrane Filter
1 FILTRATION Selecting the Best Filter for Your Application Choosing a filter does not have to be complicated – Corning has simplified the process.Just follow these four easy steps: Step 1: Match your application with the appropriate pore size. Step 2: Select the membrane and housing material for your application.
